Top of the page

d&b audiotechnik D6 amplifier, NL4

Item No. Z2700.000
Dual Channel Amplifier The 2 RU two channel lightweight D6 amplifier delivers medium power into low impedance loads between 4 and 16 ohms and is ideally suited for use in both mobile and installation environments. The D6 contains configurations for d&b loudspeakers and a linear mode; exceptions are
Login for Dealer Pricing
Click below for direct download from our manufacturers.

Description

Dual Channel Amplifier

The 2 RU two channel lightweight D6 amplifier delivers medium power into low impedance loads between 4 and 16 ohms and is ideally suited for use in both mobile and installation environments. The D6 contains configurations for d&b loudspeakers and a linear mode; exceptions are 2-Way Active, A-Series, V-Series and B2-SUB. The signal delay capability enables user definable settings of up to 340 msec (=100 m/328.1 ft) to be applied independently to each channel. The same applies to the 4-band parametric equaliser, providing optional boost/cut or notch filtering. The D6 incorporates a digital rotary encoder and a LCD display to configure the amplifier. The D6 incorporates Class D amplifiers utilising a switch mode power supply with active Power Factor Correction (PFC), suitable for mains voltages 100 V/120 V/200 V/ 230 V, 50 – 60 Hz and maintains a stable and increased output when used with weak or unstable mains supplies. It is supplied with two NL4 loudspeaker output connectors. RJ 45 connectors enable access to the Remote network via CAN-Bus. d&b System check verifies that the system performs within a predefined condition, whilst d&b Load monitoring enables an automatic and continuous impedance monitoring. Both can determine the status of an LF or HF driver in systems with multiple elements, even if these are crossed over passively.

Features
  • Maximum output power 2 x 600 W into 4 Ω
  • All current d&b loudspeaker setups except A-Series, J-Series, SL-Series, V-Series, M2, B22-SUB or 2-Way Active mode
Specifications
Data (linear setting with subsonic filter)
  • Rated output power (THD+N < 0.1%): 2 x 350 W into 8 Ω, both channels are driven, 2 x 600 W into 4 Ω, both channels are driven
  • S/N ratio (unweighted, RMS): > 110 dBr
Connectors
  • INPUT/LINK ANALOG A/B: 3 pin XLR female/male
  • INPUT/LINK DIGITAL AES/EBU: 3 pin XLR female/male
  • Sampling rate: 48 kHz / 96 kHz
  • OUT CHANNEL A/B: NL4
  • REMOTE: 2 x RJ 45 parallel
  • SERVICE: USB Type B
Digital Signal Processing
  • Sampling rate: 96 kHz / 27 Bit ADC / 24 Bit DAC
  • Basic delay / latency analog input: 0.3 ms
Power supply
  • Autosensing switch mode power supply for: 100/115/200/230V, 50 – 60 Hz
  • Mains connector: PowerCon®
Remote network
  • Remote network: CAN-Bus
Dimensions, weight
  • Height x width x depth: 2 RU x 19″ x 353 mm / 13.9″
  • Weight: 8 kg / 17.6 lb

Product Details

RRP
$ 7883.00
Brand
d&b audiotechnik
Product Group
Electonics
Product Category
Mobile Amplifier (d&b)
Item No. Z2700.000

d&b audiotechnik D6 amplifier, NL4

Dual Channel Amplifier The 2 RU two channel lightweight D6 amplifier delivers medium power into low impedance loads between 4 and 16 ohms and is ideally suited for use in both mobile and installation environments. The D6 contains configurations for d&b loudspeakers and a linear mode; exceptions are
Login for Dealer Pricing
Click below for direct download from our manufacturers.

Description

Dual Channel Amplifier

The 2 RU two channel lightweight D6 amplifier delivers medium power into low impedance loads between 4 and 16 ohms and is ideally suited for use in both mobile and installation environments. The D6 contains configurations for d&b loudspeakers and a linear mode; exceptions are 2-Way Active, A-Series, V-Series and B2-SUB. The signal delay capability enables user definable settings of up to 340 msec (=100 m/328.1 ft) to be applied independently to each channel. The same applies to the 4-band parametric equaliser, providing optional boost/cut or notch filtering. The D6 incorporates a digital rotary encoder and a LCD display to configure the amplifier. The D6 incorporates Class D amplifiers utilising a switch mode power supply with active Power Factor Correction (PFC), suitable for mains voltages 100 V/120 V/200 V/ 230 V, 50 – 60 Hz and maintains a stable and increased output when used with weak or unstable mains supplies. It is supplied with two NL4 loudspeaker output connectors. RJ 45 connectors enable access to the Remote network via CAN-Bus. d&b System check verifies that the system performs within a predefined condition, whilst d&b Load monitoring enables an automatic and continuous impedance monitoring. Both can determine the status of an LF or HF driver in systems with multiple elements, even if these are crossed over passively.

Features
  • Maximum output power 2 x 600 W into 4 Ω
  • All current d&b loudspeaker setups except A-Series, J-Series, SL-Series, V-Series, M2, B22-SUB or 2-Way Active mode
Specifications
Data (linear setting with subsonic filter)
  • Rated output power (THD+N < 0.1%): 2 x 350 W into 8 Ω, both channels are driven, 2 x 600 W into 4 Ω, both channels are driven
  • S/N ratio (unweighted, RMS): > 110 dBr
Connectors
  • INPUT/LINK ANALOG A/B: 3 pin XLR female/male
  • INPUT/LINK DIGITAL AES/EBU: 3 pin XLR female/male
  • Sampling rate: 48 kHz / 96 kHz
  • OUT CHANNEL A/B: NL4
  • REMOTE: 2 x RJ 45 parallel
  • SERVICE: USB Type B
Digital Signal Processing
  • Sampling rate: 96 kHz / 27 Bit ADC / 24 Bit DAC
  • Basic delay / latency analog input: 0.3 ms
Power supply
  • Autosensing switch mode power supply for: 100/115/200/230V, 50 – 60 Hz
  • Mains connector: PowerCon®
Remote network
  • Remote network: CAN-Bus
Dimensions, weight
  • Height x width x depth: 2 RU x 19″ x 353 mm / 13.9″
  • Weight: 8 kg / 17.6 lb

Product Details

RRP
$ 7883.00
Brand
d&b audiotechnik
Product Group
Electonics
Product Category
Mobile Amplifier (d&b)